Search:

Type: Posts; User: Strider

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    2,049

    Check out the Epson Pro 4800 to get an idea of...

    Check out the Epson Pro 4800 to get an idea of the cost of a printer that fulfills your minimum requirements.
  2. Epson and Okidata are probably the two most...

    Epson and Okidata are probably the two most common makers of impact printers.Their supplies(and parts) should be easy to find.I would get one that lets you set it for different paper thicknesses...
  3. Thread: hello thre

    by Strider
    Replies
    3
    Views
    3,174

    Have you tried Epson's web site?

    Have you tried Epson's web site?
  4. Replies
    2
    Views
    2,644

    To uninstall an epson printer(even one that has...

    To uninstall an epson printer(even one that has been'deleted')go to "start", 'programs', Epson(or Epson printers) then uninstall printers.
  5. Replies
    8
    Views
    4,455

    Like an earlier poster said,your problem is a...

    Like an earlier poster said,your problem is a flag in the fuser.The exit switch(flag) in this model is known for sticking,especially after the fuser is changed.Open the rear door and look for a black...
  6. Replies
    5
    Views
    3,709

    The jam switch actuator in your fuser is probably...

    The jam switch actuator in your fuser is probably jammed in the wrong position.If I remember right you can just reach in from the back and loosen it up.
  7. Replies
    2
    Views
    2,488

    If I remember this printer well enough,I believe...

    If I remember this printer well enough,I believe that this printer will print just fine even with this error showing.
  8. Thread: Lj4101 Mfp

    by Strider
    Replies
    4
    Views
    2,763

    First get some rubbing alcohol and clean the slit...

    First get some rubbing alcohol and clean the slit glass(small glass next to the big glass).Use a paper towel and elbow grease.If it doesn't work, use Michael's suggestions.
  9. Replies
    8
    Views
    6,265

    I don't know why no one else will give you basic...

    I don't know why no one else will give you basic info when you've asked politely.You need an impact printer(Epson and Okidata are the most common) or an inkjet that is setup for it(Epson and HP both...
  10. Replies
    2
    Views
    2,681

    1)If side-to-side alignment is off,move the...

    1)If side-to-side alignment is off,move the tractors.
    2)If items are spaced wrong,try different fonts(from printer control panel).
    3) If forms aren't fed to the right position,reset your...
  11. Replies
    1
    Views
    2,547

    Somehow you got ink on the exit rollers on the...

    Somehow you got ink on the exit rollers on the side the discs go in.If you clean them it should go away.READ your owners manual(on the installation disc)to make sure you are feeding the discs...
  12. Thread: PCL XL Error

    by Strider
    Replies
    4
    Views
    7,866

    Don, Sounds like a formatter problem.

    Don,
    Sounds like a formatter problem.
  13. Replies
    3
    Views
    2,586

    Put a piece of paper in the MP tray.Run a test...

    Put a piece of paper in the MP tray.Run a test page.Unplug the printer when the end of the paper enters the printer.Examine the area of the print that is between the toner and the fuser.If its...
  14. Thread: Hp 1200

    by Strider
    Replies
    2
    Views
    2,317

    Developing cylinder and primary charge roller are...

    Developing cylinder and primary charge roller are both part of the cartridge.Some of the common problems might be use of labels in the printer,someone who regularly takes the cartridge out and sets...
  15. Replies
    6
    Views
    3,248

    Usually with the output rollers causing...

    Usually with the output rollers causing jamming,the paper will be accordian folded in the last inch.It sounds to me like your exit switch is sticking.If you are looking at the rear of the printer its...
  16. Try cleaning the slot in the black plastic inside...

    Try cleaning the slot in the black plastic inside the printer above where the cartridge goes.That is where the laser comes through to expose the drum in the cartridge.In a laser printer,the only...
  17. Replies
    3
    Views
    5,152

    Your problem as described is almost certainly in...

    Your problem as described is almost certainly in the fuser.To be sure whether your problem is in the fuser or the toner cartridge,you could do a half-self test.Just do a search for the test on this...
  18. When using straight tcp/ip addressing for the...

    When using straight tcp/ip addressing for the printer,any changes by any user changes the settings for all users.Thats why removing their permissions worked.
  19. Replies
    6
    Views
    4,809

    Bad drum ground.To try to repair,clean all old...

    Bad drum ground.To try to repair,clean all old grease off and relube with conductive grease.
  20. Replies
    3
    Views
    2,546

    That's the sign of a corrupted print job.Removing...

    That's the sign of a corrupted print job.Removing the job from the print queue on your computer is needed to get rid of your problem.And,yes one way to do that is to uninstall and reinstall your...
  21. Replies
    1
    Views
    1,922

    Try setting tray 3 to plain paper.

    Try setting tray 3 to plain paper.
  22. Thread: HP 3550 Error

    by Strider
    Replies
    1
    Views
    2,366

    That means that the printer saw an error in the...

    That means that the printer saw an error in the printer command language.It is very common with PCL6.Some users have found that the PCL5 driver has less problems with this error.
  23. Replies
    4
    Views
    2,774

    You didn't get a paper size error because the...

    You didn't get a paper size error because the printer only checks the paper length in the feed direction,not the width.
  24. Thread: Laserjet 5200

    by Strider
    Replies
    5
    Views
    3,494

    This is a follow-up on HP's current printer...

    This is a follow-up on HP's current printer certifications.Late last year,HP changed their certification classifications.Now, techs at warranty authorized service centers get general certifications...
  25. Thread: Noisy Printer

    by Strider
    Replies
    4
    Views
    3,142

    A drop of oil at the edges of the "beads" that...

    A drop of oil at the edges of the "beads" that the belts ride on should get rid of your squeaks.
Results 1 to 25 of 99
Page 1 of 4 1 2 3 4