Search:

Type: Posts; User: cs_steve

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. That is quite an involved disassembly on your...

    That is quite an involved disassembly on your particular model.

    First, I would run the ITB CONTACT / ALIENATION test to verify that the problem is once again the fuser drive assembly (if the gear...
  2. Replies
    1
    Views
    2,263

    Most likely either a faulty Cyan or Yellow toner....

    Most likely either a faulty Cyan or Yellow toner. Pull those 2 cartridges out and flip them over to inspect the drums on the bottom of the toner. Metallic drum should be fairly clean; see if you...
  3. Replies
    2
    Views
    1,731

    I'm guessing you have the LaserJet 5L & LaserJet...

    I'm guessing you have the LaserJet 5L & LaserJet 6L? Those you might as well recycle.
    There was a plain "LaserJet 5" (no "L" designation) that has an MIO slot where you can install an HP JetDirect...
  4. "Refurbished" feeders won't contain new rollers...

    "Refurbished" feeders won't contain new rollers -- they will either be lightly-used feeders that are "cleaned up" or the feeders were rebuilt by harvesting decent parts from other broken feeders. ...
  5. Replies
    2
    Views
    2,449

    Definitely sounds like a timing issue; the...

    Definitely sounds like a timing issue; the second-stage of the duplexing is somehow entering the path too early and zipping past the toner cartridges before they can lay down a print. I would try...
  6. Sounds like 2 bad toner cartridges in a row. Old...

    Sounds like 2 bad toner cartridges in a row. Old stock HP cartridges are prone to failure just sitting on the shelf ; some of them are 15+ years old.
    It's difficult to find a good quality cartridge...
  7. Thread: HP LJ Pro 400

    by cs_steve
    Replies
    1
    Views
    7,127

    If you want to post a photo of the defect it...

    If you want to post a photo of the defect it might help.

    Normally we would blame light print on faulty toner cartridges; if the cartridges are aftermarket brand then I could see 2 sets in a row...
  8. Replies
    1
    Views
    6,293

    Sounds like the onboard Ethernet connection is...

    Sounds like the onboard Ethernet connection is starting to fail. That is part of the formatter which is the main system board. You could order another formatter board, here's a link....
  9. Replies
    1
    Views
    2,491

    That error code is pretty specific, something is...

    That error code is pretty specific, something is wrong with the Yellow laser scanner error. Either you are not replacing the correct laser scanner or there is a problem with the ones you are...
  10. Replies
    2
    Views
    3,439

    If you don't want to replace the whole system,...

    If you don't want to replace the whole system, you could just try a different fuser and see if it works better with your envelopes --...
  11. Replies
    2
    Views
    3,243

    Sounds like something is wrong with the fuser not...

    Sounds like something is wrong with the fuser not turning ... what model printer is this? My first instinct is something may be wrong with the fuser you just installed and you might need a warranty...
  12. Replies
    2
    Views
    4,700

    The key is to observe the pickup rollers during...

    The key is to observe the pickup rollers during failure -- if the rollers are touching the paper and spinning but the paper is not moving, I would replace those rollers as they are losing grip. These...
  13. Replies
    1
    Views
    2,990

    Two questions -- 1. Is this printer connected...

    Two questions --
    1. Is this printer connected via USB?
    2. Are you for some reason disconnecting the USB cable occasionally?

    If you are disconnecting the USB cable occasionally, you should...
  14. If you have the 4050N model (not the 4050TN) it...

    If you have the 4050N model (not the 4050TN) it doesn't involve a full disassembly, just a little access panel inside the paper tray cavity. Here's a link to accessing that PCA board --...
  15. That sounds like the transfer belt assembly is...

    That sounds like the transfer belt assembly is failing / not cleaning properly; it is a consumable part so should be something you can change yourself, it is located just below the fuser assembly. ...
  16. Replies
    1
    Views
    4,345

    Since you've already changed the Magenta (pink)...

    Since you've already changed the Magenta (pink) toner, I suspect the Magenta drum unit is failing. We carry replacement drum units at PrinterTechs (866-352-7108).
  17. Replies
    2
    Views
    3,087

    There is no documentation available for these...

    There is no documentation available for these kinds of individual board-level components. HP intended for faulty boards to be replaced rather than repaired so you really can't find pin-out...
  18. Replies
    1
    Views
    3,213

    There is a solenoid that can get gummy/sticky...

    There is a solenoid that can get gummy/sticky with time, for Tray 2, that will stick during pickup and cause an extra sheet to feed. It's involved to access it, you have to remove covers &...
  19. Sounds like the formatter assembly is failing;...

    Sounds like the formatter assembly is failing; the formatter assembly is the main logic board and is a common failure part on this model. Replacing the formatter is not difficult, here is a link to...
  20. My guess is the noise is probably coming from a...

    My guess is the noise is probably coming from a faulty toner cartridge , that's the most common issue. If replacing the toner cartridge doesn't help, it could possibly be the laser scanner but it's...
  21. Replies
    4
    Views
    10,260

    Sounds like a sticking solenoid ; over time the...

    Sounds like a sticking solenoid ; over time the sound dampening pad gets "gummy" and causes the solenoid to stick intermittently. On this model it is a big job to disassemble and access the...
  22. Replies
    1
    Views
    2,920

    If the roller isn't spinning (you can watch it...

    If the roller isn't spinning (you can watch it when you fold down the manual feed tray) then yes, something is off with either the solenoid or the drive mechanism for manual feed roller. Solenoids...
  23. You mention fading up the center when copying; do...

    You mention fading up the center when copying; do prints from your PC or internal test pages from the printer show the same fading? If this only happens with copies, then you should clean the glass...
  24. Replies
    3
    Views
    3,970

    Can't post pricing here but will PM you.

    Can't post pricing here but will PM you.
  25. Replies
    3
    Views
    3,970

    Unfortunately that motor just isn't available...

    Unfortunately that motor just isn't available individually -- we (PrinterTechs) do carry the entire paper pickup assemblies (RG5-6208).
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4