Search:

Type: Posts; User: MichaelTech

Page 1 of 20 1 2 3 4

Search: Search took 1.78 seconds.

  1. Replies
    3
    Views
    4,589

    Your showing just the P/S, but have you checked...

    Your showing just the P/S, but have you checked the H/V contacts? A faulty one could affect the fuser, and may cause the fading. Drum drawer contacts, on the sides of the drawer, and the small round...
  2. Replies
    5
    Views
    7,359

    Possibility of the H/V being full of toner, and...

    Possibility of the H/V being full of toner, and shorting a bit. Pull tray, lift printer on its back, two screws, pull off H/V and clean.
  3. Replies
    1
    Views
    3,115

    Aftere swapping everything but the MDA off a...

    Aftere swapping everything but the MDA off a working unit, still not right.
    just went ahead and swapped the new unit to close the call.
    So, if all the parts I tried, and they all were good, Im...
  4. I dont think it's the fuser. The defect is...

    I dont think it's the fuser. The defect is ghosted about three inches, so it will be one of the toners that is the issue.
  5. Replies
    1
    Views
    3,115

    CLJ4700 MDA gears

    Howdy all, I have an issue with timing on the disengagement drive sensor.
    Sensor test is ok.
    Does the slot on the gear that passes through the sensor affect it?
    Im getting only half a page, with...
  6. Replies
    1
    Views
    2,978

    This is the acuators for the tray. It pushes the...

    This is the acuators for the tray. It pushes the buttons on the PCB.
  7. catchers mitt.

    catchers mitt.
  8. Replies
    2
    Views
    4,241

    Oh yeah, and it too was a thought. I was right...

    Oh yeah, and it too was a thought. I was right about the Drive Release Assy. It, and only it power the fuser drive. Replaced it, and the fuser drive assy, done. Purrs!.
  9. Replies
    2
    Views
    4,241

    New take on a P3005 noise.

    I have changed the fuser 3times, all four gears in the pendulum assy., but still that damn noise!
    In removing the entire fuser drive assy, and the main drive assy., I see that only one spring...
  10. Replies
    4
    Views
    7,206

    MichaelTech

    No paper anywhere, then it may be a pick-up issue. Change both rollers under the printer? The tray should have it's replaced too. Tightnening a screw in the delivery is not necessary. It's flag may...
  11. Replies
    1
    Views
    3,015

    How many USB ports are you using? You may need an...

    How many USB ports are you using? You may need an external box, be sure to load the drivers for it. If you network is using shared ports, change that. Win 7 drivers arent too great on XP's.
  12. You have a fax/printer. Go into the fax setup and...

    You have a fax/printer. Go into the fax setup and remove the header. Not sure if resets will change it, but if there is a menu for it try. I dont have any guide, but you can search it, and find...
  13. Replies
    9
    Views
    8,376

    Color printing is expensive. You have an...

    Color printing is expensive. You have an expensive printer. Spend the money for good consumables! Trying to get by on the cheap will just get you that.
  14. Replies
    6
    Views
    14,288

    have you checked the toner alienation bar on the...

    have you checked the toner alienation bar on the left side? Some teeth may have broken off, and if the toner is'nt positioned right may give you this scanner error.
    Check top and bottom of plate.
  15. Right, cs_steve, and they are usually tested on...

    Right, cs_steve, and they are usually tested on the correct machine by reputable dealers. Refurbed DC's can be an issue also, if NVRAM is blank. Try printertechs for replacement parts. It will be...
  16. Any memory? Need at least a 64 MB chip to...

    Any memory? Need at least a 64 MB chip to initialize network. If have, must turn on in menu on printer. Or add a NIC card, and it willl be seen. If not, replace formatter.
    Ensure it is the correct...
  17. Replies
    8
    Views
    8,498

    Light print is mostly a H/V issue or a scanner...

    Light print is mostly a H/V issue or a scanner issue. Going light then dark, then light again would idicate either of these two. Try a firmware update even if same.
  18. Replies
    3
    Views
    4,602

    Check the fuser drive? It could be stalling, or...

    Check the fuser drive? It could be stalling, or the motor quits.
    The ETB could be the culprit also. Cassette drive motor goes bad a lot on these too.
    It's a reversing motor as it drives both the MP...
  19. Is the spring on the sensor flag? It can get...

    Is the spring on the sensor flag? It can get weak, and if woudn to many times, can be too short, and slip into the cavity. Order the flag and spring when ordering the paper feed assy.
  20. Replies
    3
    Views
    4,402

    You have a cam slide: RC1-6638 Also you may need...

    You have a cam slide: RC1-6638 Also you may need the Left link rod: RC1-6639
  21. Replies
    0
    Views
    2,011

    Epson Adjustments

    This program is in my 1280 manual, but I cant find it anywhere. All links when I google, are just for the resetter, I need the entire Adjustment Repair Program. Anyone?
    Epson is being ignorant of...
  22. It's in the Configuration Menu. Also check the...

    It's in the Configuration Menu. Also check the driver settings match the printer panel settings.
  23. Check fuser settings in the control panel. Also...

    Check fuser settings in the control panel. Also check small paper mode set to normal.
    Turn duplex off if not using.
  24. Replies
    4
    Views
    9,564

    Power to the scanner can affect it if not...

    Power to the scanner can affect it if not correct. The power supply next to the DC may be the issue.
  25. Replies
    7
    Views
    7,371

    The black piece is from the rear door, not...

    The black piece is from the rear door, not crucial.
    If you can not even get a config page out, the formatter may be a problem. Put the JD card in the other slot. The JD may be bad. Or the slot is....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4