Search:

Type: Posts; User: ptjeff1

Page 1 of 13 1 2 3 4

Search: Search took 0.03 seconds.

  1. My first thought is that it is a sticking...

    My first thought is that it is a sticking solenoid for the tray 2 pickup assembly, not the paper size pca.
  2. Thread: Dead Forum?

    by ptjeff1
    Replies
    2
    Views
    695

    I guess printers are dead... or disposable. ...

    I guess printers are dead...

    or disposable.

    You have a question?
  3. It sounds like you went through a lot of good...

    It sounds like you went through a lot of good troubleshooting. Humidity was my first thought. Make sure you are setting the humidity compensation under the right paper type. Administration>general...
  4. Replies
    2
    Views
    945

    That looks like a toner problem. Maybe 2 bad...

    That looks like a toner problem. Maybe 2 bad toners or check the toner contacts in the printer to make sure they touch the metal contacts on the toner cartridge.
  5. Replies
    1
    Views
    1,716

    It would help if you told us what you are trying...

    It would help if you told us what you are trying to do. It seems like you don't want the toner to fuse completely. Removing the pressure roller means you'll likely get a paper jam; in most printers...
  6. Replies
    3
    Views
    1,273

    Whatever you do, don't try to clean the transfer...

    Whatever you do, don't try to clean the transfer roller with any liquids, only use compressed air or a dry cloth.

    Try a half-way test...
  7. Replies
    1
    Views
    883

    Yes, probably the laser scanner.

    Yes, probably the laser scanner.
  8. Replies
    1
    Views
    6,867

    Lan hardware address is the mac address,...

    Lan hardware address is the mac address, sometimes it is printed on the barcode on the card
  9. Replies
    0
    Views
    9,893

    13.A2.FF error HP Laserjet M601, M602 M603

    We had a customer trying to figure out a 13.A2.FF error in an HP M60x series, also gave a 13.FF.FF error. The 13.A2.FF error code isn't listed in the service manual, other sites suggest paper or dust...
  10. Replies
    2
    Views
    1,331

    Does the memory count up and do you see the HP...

    Does the memory count up and do you see the HP logo on the screen?
    If there is a Jetdirect card or extra memory installed remove them and power up to see if the problem goes away.
  11. Replies
    9
    Views
    6,169

    The first thing to test is to make sure the...

    The first thing to test is to make sure the memory is good, also remove the Jetdirect card if there is one installed, if there is a firmware dimm that would also need to be checked.
  12. Replies
    0
    Views
    916

    spammers go away!!

    OK, I just deleted hundreds of spam posts, and because of that we will have to take the step to approve all new members. All new users will be placed into a validation queue for approval before they...
  13. Replies
    5
    Views
    3,988

    I've been meaning to reply to this post for a...

    I've been meaning to reply to this post for a while...I wasn’t aware that there were any doubts in the printer tech community regarding the metal gear.

    This is a rough sketch showing how the...
  14. FYI there is only one OEM -- HP. Most aftermarket...

    FYI there is only one OEM -- HP. Most aftermarket transfer rollers for these models are notorious for poor print quality when duplexing.
  15. Replies
    2
    Views
    5,561

    yes, and yes...the factory defaults were restored...

    yes, and yes...the factory defaults were restored and nvram reset with no effect. The key here is printing an engine test, which in this case was perfect, pointing to the formatter.
  16. Replies
    2
    Views
    5,561

    CM2320 color registration problem - fixed

    just posting this to help anyone else who might see this problem. It has to do with color registration problems in the HP color laserjet CM2320 series, CM 2320fxi mfp, etc.

    People would probably...
  17. Replies
    5
    Views
    3,988

    Hi Stewart -- we have tested our metal swing...

    Hi Stewart -- we have tested our metal swing plate gear to over 1 million pages worth of use. At 1 million pages the gear still worked flawlessly. The teeth started to show some minor wear but I...
  18. Replies
    8
    Views
    3,062

    Formatters on the P2015 have been a high failure...

    Formatters on the P2015 have been a high failure part, my advise is to replace the printer. Formatters are generally $100+. If you really like the design of the P2015 consider the previous model the...
  19. Replies
    2
    Views
    1,404

    many people describe the laser scanner spinning...

    many people describe the laser scanner spinning up as a jet-like sound. You could try replacing the scanner, but they all make some noise.
  20. Replies
    12
    Views
    16,847

    In know this is sarcastic, but a Deskjet 6940 is...

    In know this is sarcastic, but a Deskjet 6940 is a $99 printer. I wouldn't have high expectations. I didn't search very hard but it wouldn't surprise me if this were a host based printer, which...
  21. Replies
    1
    Views
    789

    Article: Managing CMS Section and Content

    You can view the page at http://printertechsforum.com/forum/content.php?93-Managing-CMS-Section-and-Content
  22. Replies
    2
    Views
    1,825

    yes

    yes, old threads are still here.

    Towards the bottom of the forum page, you should see an area titled Thread Display Options, and you'll see: "Show threads from the..." select from the beginning...
  23. Thread: Stars!!!!!!

    by ptjeff1
    Replies
    2
    Views
    1,805

    spammers

    spammers just keep coming back, I suspect they are sitting in some room in China getting paid 20 cents an hour to post links to spam websites.
  24. Did you try a postscript driver? You didn't...

    Did you try a postscript driver? You didn't mention the operating system you are using, or maybe I missed it.
  25. Replies
    2
    Views
    1,796

    check the bottom metal plate of the printer, if...

    check the bottom metal plate of the printer, if it is bent upwards you will get a 60.2 error. We have seen this in cases of shipping damage.
Results 1 to 25 of 324
Page 1 of 13 1 2 3 4