The left margin is too far to the left, to point nearly off the page, even on a engine test page and configuration, where the lines normally is blank.
Paper guides are set right, and problem does...
Type: Posts; User: woodss
The left margin is too far to the left, to point nearly off the page, even on a engine test page and configuration, where the lines normally is blank.
Paper guides are set right, and problem does...
Here is a video report, about my thoughts about the gear.
http://youtu.be/H9V6Z1Pl5z8
This investigation has found that there is skeptics of the metal swing plate gear, some technicians think...
Is there a chance of the metal gear to ruin the white gear of the swing plate assembly?
There is some in the laser printer industry that feel that this metal gear will cause the white gear to fail,...
It prob last for 32 years then, with my level of use.
Printer would have died by then.
I only have done nearly 60,000 copies in 2 years, only lightly used.
How long would it take to print one...
I have purchased a Swing Plate Kit from this printertechs company, the customer service was superb and, Steve was a great sales person.
My question is how long will the metal swing plate gear last...
Excellent Link, sometimes doing the trick with a hard piece of cardboard, can actually correct the problem, sometimes a 13.20 error on this series can be corrected per the instructions with that link.
I perhaps already know the soultion anyway, but I thought to share it with you all, I have a 4300 DTN that turns on, motor runs only breifly, then goes though the self test and then after that the...
Thats how I started in 2001, most senior techs here learnt with the school of hard knocks, one technician named Moe in Califorina learnt printer repair from just working out how to take them apart...
Not worth it.
You can open up the power supply and inspect the componets, if any are burnt, you can replace them, they are all standard componets and this is the good thing about older machines,...
The LaserJet 4 Series is still a reliable printer, just needs more care as they are a older machine, but if you service them well and fix all the known faults then the machine will work for a decade...
Or a bad duplexer solenoid.
Might be good idea to retire the old thing but sometimes dust can get inside the laser scanner usually a blow with compressed air can fix these problems, but 4MP are very slow, 4ppm, the 4000TN is a...
might be wise for you to get a proper color copier.
I use a Fuji Xerox Docu Center C400
might be toner or fuser
half test is the tool to be used to determine this in this case.
place a piece of paper into tray one, do a test page and when the paper reaches nearly into the machine...
I had a LaserJet 1300 model after the 1200 that did that as well, I have found for which a stuck solenoid causes the pickup system to have a second or third rotation, when it should be just one,...
Hi Everyone, I have some tip to give out for those for which installing the swing plate assembly on the LaserJet 4200, 4300, 4250 and 4350 series printers.
I have found that there is a...
replace the following parts:
feed assembly
4 pickup rollers that are shaped of the letter D these are in tray 2
2 Feed rollers also in tray 2
Torque Limiter
Clean the soleniod in tray 2...
hp likes to mislead people, they know the truth but only reserved to their service centers.
the sensors might need a clean due to being stuck.
maybe a mix of toner and paper dust which can turn to a messy gunk.
I did a cold reset, to the machine no effect but it reset the machine back to factory defaults.
You can buy the chips from toner remanufacturers some will sell it some wont.
problem solved, changing the toner chip cured the problem.
when will the chip go back to the toner level which was 77% now its 99% how does the printer do this?
Is there a way to force the...
I tend to agree with what advice that was being said in here.
I always tend to think that these newer low end products have lost their quality, I tend to like the older models, they have proven...
i have ordered another chip for the toner, if that wont solve the issue what is the next step.
I have a 6 year old, Color LaserJet 5500DTN it was working fine a 2 days ago, then there was a drop in temprature as it lives in the garage.
However, I was using it that morning for new years eve...
the transfer roller is a oem roller from a repair kit.